INSTALLATION MANUALSAVE THIS MANUAL!Include it with the backhoe manual. It contains safety, operation, and repair part information not found in other
10 InstallationMAN0406 (Rev.9/7/2007)Torque Mounting HardwareAttach Backhoe Mounts to BackhoeNOTE: Leave all hardware loose until backhoe hasbeen mou
Installation 11MAN0406 (Rev. 9/7/2007)HYDRAULIC INSTALLATION Keep hands and body away from pressurizedlines. Use paper or cardboard, not hands or oth
12 InstallationMAN0406 (Rev.9/7/2007)Install Hydraulic Block and Fittings1. Locate the hydraulic manifold block on the rightside of the tractor just
Installation 13MAN0406 (Rev. 9/7/2007)Install Bulkhead Adapter on Backhoe Mount1. Attach bulkhead adapter (1) to crossmemberbetween backhoe brackets
14 InstallationMAN0406 (Rev.9/7/2007)Mount Backhoe to Tractor This mounting kit is designed to providesecure mounting and adequate operator clear-anc
Installation 15MAN0406 (Rev. 9/7/2007)Mount Backhoe to Tractor (Continued) Refer to Figure 26.5. Using the backhoe hydraulics position the back-hoe
16 InstallationMAN0406 (Rev.9/7/2007)Remove Backhoe from Tractor The only time the backhoe may be operatedfrom a position other than the operator sea
Installation 17MAN0406 (Rev. 9/7/2007)STORAGEConnect Hydraulic Hoses TRACTOR: Connect male quick coupler on end ofhose to female quick coupler at bul
18 PartsMAN0406 (Rev. 9/7/2007)1013460 4-POINT SUB-FRAME MOUNTING KITW A RNINGPINCH POINTKeep hands clear.1006885 31 - PN 1006885MODEL NO. SERIAL NO.W
Parts 19MAN0406 (Rev. 9/7/2007)1013484 HOSE KITREF PART QTY DESCRIPTION1 1006144 1 Adapter, bulkhead3/8 NPTM x 3/4 JICM2 1009493 1 Hose, 40" x 3/
2 IntroductionSFMK (Rev. 2/20/2008)TO THE DEALER:Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read man
20 AppendixBolt Torque & Size Charts (Rev. 3/28/2007)BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or t
Appendix 21Bolt Torque & Size Charts (Rev. 3/28/2007)BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for
F-8494 (Rev. 6/23/2005)WARRANTY(Replacement Parts For All Models Except Mow’n MachineTMZero-Turn Mowers and Woods BoundaryTM Utility Vehicles)Woods Eq
F-3079 (Rev. 4/4/2008)WARRANTY(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)Please Enter Information Below
PART NO.MAN0406© 2005 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks
Safety 34-Point SFMK (Rev. 5/8/2006)SAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! This Sub-Frame Mounting Kit is only for thebackhoes
4 Safety4-Point SFMK (Rev. 5/8/2006)SAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!(Safety Rules continued from previous page) Make sur
Installation 5MAN0406 (Rev. 9/7/2007)BACKHOE SUB-FRAME INSTALLATIONTractor Preparation Only use 1013460 4-Point Sub-Frame Mount-ing Kit for mountin
6 InstallationMAN0406 (Rev.9/7/2007)Install Front MountsWith Woods LS84 Loader MountAttach front mount (32) to the right loader mountusing two cap scr
Installation 7MAN0406 (Rev. 9/7/2007)Install Tractor BracketsWith Woods LS84 Loader Mount1. Place left tractor bracket (2) under left side oftractor
8 InstallationMAN0406 (Rev.9/7/2007)Install Tractor Brackets1. Place left tractor bracket (2) under left side oftractor. Use a hydraulic floor jack
Installation 9MAN0406 (Rev. 9/7/2007)Install Cross Brace1. Remove PTO shield.2. Attach cross brace (7) to rear of tractor using twocap screws (24)
Comments to this Manuals