Woods Equipment SG100 User Manual

OPER ATOR'S MANUALSTUMP GRINDERMAN0155 (Rev. 2/16/2007)Tested. Proven. Unbeatable.SG100

10 OperationMAN0155 (Rev. 2/16/2007)OPERATIONThe operator is responsible for the safe operation ofthis stump grinder. The operator must be properlytra

Operation 11MAN0155 (Rev. 2/16/2007)4. Grease slip joint on driveline.NOTE: Check gearbox oil level daily after initialstart up. Figure 3. Lubricatio

12 OperationMAN0155 (Rev. 2/16/2007)8. Attach quick couplers to tractor hydraulic source.9. Place jack stand in storage position.OPERATING TECHNIQUE1.

Operation 13MAN0155 (Rev. 2/16/2007)PRE-OPERATION CHECK LIST(OWNER'S RESPONSIBILITY)___ Review and follow all safety rules and safetydecal instru

14 Owner ServiceMAN0155 (Rev. 2/16/2007)OWNER SERVICEThe information in this section is written for operatorswho possess basic mechanical skills. If y

Owner Service 15MAN0155 (Rev. 2/16/2007)ADJUSTING SLIP CLUTCHThe slip clutch is designed to slip so that the gearboxand driveline are protected if the

16 Dealer ServiceMAN0155 (Rev. 2/16/2007)DEALER SERVICEThe information in this section is written for dealer ser-vice personnel. The repair described

Dealer Service 17MAN0155 (Rev. 2/16/2007) Figure 11. Gearbox and Driveline Seal Replacement (Figure 12)Recommended sealant for gearbox repair is Perma

18 Dealer ServiceMAN0155 (Rev. 2/16/2007) Figure 13. Gearbox DisassemblyInput Leak RepairRefer to Figure 13.1. Disconnect and remove the rear drivelin

Dealer Service 19MAN0155 (Rev. 2/16/2007)15. Remove bottom bearing (6) by using a punch andhammer from the top, outside the housing.Support housing up

2 IntroductionGen’l (Rev. 2/5/2007)TO THE DEALER:Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read man

20 Dealer ServiceMAN0155 (Rev. 2/16/2007)21. Install gearbox into stump grinder. Reverse steps inRemove Gearbox from Stump Grinder, page 16 toinstall

Dealer Service 21MAN0155 (Rev. 2/16/2007)3. Clamp cup in vise as shown in Figure 19 and tapon yoke to completely remove cup from yoke.Repeat Step 2 an

22 Dealer ServiceMAN0155 (Rev. 2/16/2007)NOTES

Dealer Check Lists 23MAN0155 (Rev. 2/16/2007DEALER CHECK LISTSPRE-DELIVERY CHECK LISTDEALER’S RESPONSIBILITYInspect stump grinder thoroughly after ass

24 PartsMAN0155 (Rev. 2/16/2007)STUMP GRINDER ASSEMBLY38 - SAFET DECAL SET

Parts 25MAN0155 (Rev. 2/16/2007)STUMP GRINDER PARTS LISTREF PART QTY DESCRIPTION1 1004500 25 Carbide tooth w/bolt & lock nut2 1004505 1 Jack stand

26 PartsMAN0155 (Rev. 2/16/2007)GEARBOX ASSEMBLYREF PART QTY DESCRIPTION1 1004531 1 Gear crown Z19 M82 N/S 1 Gearbox housing3 1004532 1 Shaft input 1-

Parts 27MAN0155 (Rev. 2/16/2007)DRIVELINEREF PART QTY DESCRIPTION1 1001325 1 Coupler collar yoke2 30962 2 U-Joint repair kit3 1004549 1 Inner yoke &am

28 AppendixBolt Torque & Size Charts (Rev. 10/10/2005)BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or

Appendix 29Bolt Torque & Size Charts (Rev. 10/10/2005)BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for

Introduction 3MAN0155 (Rev.2/16/2007)TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

F-8494 (Rev. 6/23/2005)Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxw

F-3079 (Rev. 1/16/2007)Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxw

PART NO.MAN0155© 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks

4 IntroductionMAN0155 (Rev. 2/16/2007)SG100 SPECIFICATIONSWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety 5SG100 Safety Rules (Rev. 6/16/2006)TRAINING Safety instructions are important! Read allattachment and power unit manuals; follow allsafety ru

6 SafetySG100 Safety Rules (Rev. 6/16/2006)(Safety Rules continued from previous page) Avoid contact with electrical wires. Keep hands, feet, hair,

Safety 7SG100 Safety Rules (Rev. 6/16/2006) Keep all persons away from operator controlarea while performing adjustments, service, ormaintenance. Ti

8 SafetySG100 Safety Rules (Rev.2/16/2007)SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Replace Immediately If Dam

Safety 9SG100 Safety Rules (Rev. 2/16/2007)SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Replace Immediately If Da