OPER ATOR'S MANUALSNOWBLOWERMAN0869 (Rev. 12/6/2011)SB54SSB64SSB74CSB84C
10 OperationMAN0869 (04/13/2011)OPERATIONThe operator is responsible for the safe operation ofthe snowblower. The operator must be properlytrained. Op
Operation 11MAN0869 (04/13/2011)The snowblower is mounted on a tractor 3-point hitchand driven by the tractor PTO. A centrally located gear-box direct
12 OperationMAN0869 (04/13/2011)SHORTENING DRIVELINE1. Move snowblower up and down to get shortestpossible distance between tractor PTO shaft andgea
Operation 13MAN0869 (04/13/2011)4. Check oil level in the gearbox. Add as required.5. Lubricate all grease points.B. After operating for 5 to 10 h
14 OperationMAN0869 (04/13/2011)prevent deflector damage and improve resolutionof deflector adjustment. Adjusting Discharge Chute Position The heig
Operation 15MAN0869 (04/13/2011)6. Lubricate all grease fittings. Make sure that allgrease cavities have been filled with grease toremove any water
16 Owner ServiceMAN0869 (04/13/2011)OWNER SERVICEThe information in this section is written for operatorswho possess basic mechanical skills. Should y
Owner Service 17MAN0869 (04/13/2011)4. Apply one pump of grease to each driveline u-jointgrease fitting.5. Apply one pump of grease to each of the
18 Owner ServiceMAN0869 (04/13/2011)Auger Drive Shear Bolt Replacement Always use approved shear bolt as replace-ment part. Using a hardened bolt
Owner Service 19MAN0869 (04/13/2011)1. Place a 4" x 4" block under each end of snow-blower frame. NOTE: Block only high enough for the sk
2 IntroductionGen’l (Rev. 12/5/2011)TO THE DEALER:Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read ma
20 Owner ServiceMAN0869 (04/13/2011)TROUBLE SHOOTINGPROBLEM PROBLEM CAUSES SUGGESTED SOLUTIONPTO Shaft shear bolt continuesto shearPTO shaft at too gr
Assembly 21MAN0869 (04/13/2011)ASSEMBLY INSTRUCTIONSDEALER SET-UP INSTRUCTIONSAssembly of this snowblower is the responsibility of theWoods dealer. It
22 AssemblyMAN0869 (04/13/2011)NOTE: Make sure handle will not protrude into rearwindow of a tractor equipped with cab by checkingthe highest 3-point
Assembly 23MAN0869 (04/13/2011)MOUNTING HYDRAULIC CHUTE ROTA-TOR OPTION (FIGURE 22)1. Fasten coupler (7) to hydraulic motor (1) usingwoodruff key an
24 AssemblyMAN0869 (04/13/2011)MOUINTING HYDRAULIC CHUTE DEFLEC-TOR (FIGURE 25)1. Fasten cylinder (1) to discharge chute (8) usinghardware (6) and (
Assembly 25MAN0869 (04/13/2011)MOUNTING ELECTRIC CHUTE DEFLEC-TOR (FIGURE 26)1. Install remote deflection option by fastening actua-tor (14) using c
26 Dealer Check ListsMAN0869 (04/13/2011)DEALER CHECK LISTSPRE-DELIVERY CHECK LIST(Dealer Responsibility)Inspect the equipment thoroughly after assemb
Parts 27MAN0869 (04/13/2011)PARTS INDEXSB54S & SB64S ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 - 29SB74C &
28 PartsMAN0869 (04/13/2011)SB54S, SB64S SUBCOMPACT SNOWBLOWER ASSEMBLY(Rev. 10/4/2011)
Parts 29MAN0869 (04/13/2011)SB54S, SB64S SUBCOMPACT SNOWBLOWER PARTS LISTREF PART QTY DESCRIPTION1 1033318 1 Fan2 1033190 3 Bearing3 29893 * 4 1/2 NC
Introduction 3MAN0869 (04/13/2011)TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30 PartsMAN0869 (04/13/2011)SB74C, SB84C COMPACT SNOWBLOWER ASSEMBLY(Rev. 10/4/2011)
Parts 31MAN0869 (04/13/2011)SB74C, SB84C COMPACT SNOWBLOWER PARTS LISTHAND CRANK ASSEMBLYREF PART QTY DESCRIPTION1 1033218 1 Fan2 1033190 3 Bearing3 2
32 PartsMAN0869 (04/13/2011)GEARBOX ASSEMBLYREF PART QTY DESCRIPTION1 438 4 Ball Bearing2 20901 3 Seal3 1007866 4 Shim Pack4 307126 8 M8 x 55 Socket H
Parts 33MAN0869 (04/13/2011)1031908 - COMER SHEAR BOLT DRIVE ASSEMBLY (OPTIONAL)SB54S, SB64SREF PART QTY DESCRIPTIONA 1031908 1 Complete 540 driveline
34 PartsMAN0869 (04/13/2011)1031826 - COMER SHEAR BOLT DRIVE ASSEMBLY (OPTIONAL)SB74C, SB84CREF PART QTY DESCRIPTIONA 1031826 1 Complete 540 driveline
Parts 35MAN0869 (04/13/2011)1033266- WALTERSCHEID DRIVE ASSEMBLY (OPTIONAL)SB54S, SB64S, SB74C, SB84CREF PART QTY DESCRIPTIONA 1033266 1 Complete 540
36 PartsMAN0869 (04/13/2011)HYDRAULIC CHUTE ROTATOR (OPTIONAL)HYDRAULIC CHUTE DEFLECTOR (OPTIONAL)REF PART QTY DESCRIPTION1 90405236 1 Hydraulic Motor
Parts 37MAN0869 (04/13/2011)ELECTRIC CHUTE ROTATOR (OPTIONAL)ELECTRIC CHUTE DEFLECTOR (OPTIONAL)REF PART QTY DESCRIPTION1 12030819 1 Rotary Actuator2
38 AppendixBolt Torque & Size Charts (Rev. 3/28/2007)BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or t
Appendix 39Bolt Torque & Size Charts (Rev. 3/28/2007)BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for
4 IntroductionMAN0869 (04/13/2011)SPECIFICATIONSWidth Of Cut: . . . . . . . . . . . . . . . . . . SB54S . . . . . . . . . . . . . . . . . . . . . . .
F-3079 (Rev. 2/14/2011)Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA800-319-6637 tel800-399-6637 f
F-8494 (Rev. 10/3/2011)WARRANTY(Replacement Parts For All Models Except Mow’n MachineTMZero-Turn Mowers)Woods Equipment Company (“WOODS”) warrants thi
Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061815-732-2141 tel815-732-7580 faxwww.WoodsEquipment.comMAN
Safety 5Snowblower_SRs (04/13/2011)TRAINING Safety instructions are important! Read allattachment and power unit manuals; follow allsafety rules and
6 SafetySnowblower_SRs (04/13/2011) Do not operate or transport equipment whileunder the influence of alcohol or drugs. Operate only in daylight or
Safety 7Snowblower_SRs (04/13/2011)Make sure shields and guards are properlyinstalled and in good condition. Replace if damaged. Do not disconnect h
8 SafetyMAN0869 (04/13/2011)4 - 1033602 1 - 1033600 5 - 10332707 - 1033601SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INV
Safety 9MAN0869 (04/13/2011)BE CAREFUL!Use a clean, damp cloth to clean safety decals.Avoid spraying too close to decals when using a pressure washer;
Comments to this Manuals